外文翻譯--馬自達公司的速度感應四輪轉向系統

《外文翻譯--馬自達公司的速度感應四輪轉向系統》由會員分享，可在線閱讀，更多相關《外文翻譯--馬自達公司的速度感應四輪轉向系統（9頁珍藏版）》請在裝配圖網上搜索。

1、The Mazda Speed Sensing Computerised 4-Wheel Steering System. Three and a half decades ago, two young Mazda designers arrived at a far-sighted and well-calculated conclusion that was quite revolutionary for the time. In their technical presentation at the October 26, 1962 Japanese Automotive Enginee

2、rs Society Technical Conference, Dr Tadashi Okada and engineer Toshiaki summarised their arduous research concerning vehicle dynamics as follows. 1. The basic difference in the characteristics of oversteer and understeer lies in the magnitude of time delay and response. 2. a vehicle that is stable u

3、nder high speed must possess understeer characteristics 3. the rear wheel tyre reflects heavily on the stability and 4. a major improvement on control and stability may be anticipated by means of the automatic rear wheel steering system. The conclusions and formulations presented by these two engine

4、ers established the foundation for Mazdas present-day reputed suspension technology. Over years of dedicated research and development expertise, their original discoveries and theories have contributed to some of the most significant achievements within the recent history of automotive chassis engin

5、eering, incorporated by Mazda within its series production products. These developments include the twin trapezoidal link rear suspension, first employed in the original front-wheel drive Mazda 323 (1980) and the Mazda 626 (1982), and then perfected within the updated Mazda 626; the award winning Dy

6、namic Tracking Suspension System of the second generation Mazda RX-7 (1985); and the elaborate E-link rear suspension of the new Mazda 929 (1987). While various external forces and loads are exerted to the rear wheels of a vehicle as it combats the elements of the law of motion as defined by Sir Isa

7、ac Newton, these new suspension systems convert those forces into 4WS effects which positively aid in vehicle stability and agility. The Mazda designers and engineers ultimate goal was still a positive measure to generate forces for positive controls; a Four-Wheel Steering system. In 1983, Mazda ast

8、onished the automotive world with the introduction of an engineering concept car, the MX-02, exhibited at the Tokyo Motor Show. This four-door Sedan, with generous passenger accommodation on an unusually long wheelbase, incorporated among its numerous advanced features a true 4WS system that aided h

9、igh-speed stability as well as its low-speed manoeuvring. The degree of rear wheel steering was determined by the measurement of both front wheel steering angle and vehicle speed, by means of a central computer unit. The MX-02 was followed by another exciting concept car; the MX-03, first exhibited

10、at the Frankfurt Motor Show in September 1985. This sleek four seat futuristic coupe of the 1990s combined a refined electronically-controlled 4WS system with a continually varying torque-split, four-wheel drive system and a powerful three-rotary engine. Mazda Electronically -Controlled Four-Wheel S

11、teering System: A Beneficial Technology Mazdas electronically-controlled, vehicle-speed-sensing Four-Wheel Steering System (4WS) steers the rear wheels in a direction and to a degree most suited to a corresponding vehicle speed range. The system is mechanically and hydraulically actuated, producing

12、greatly enhanced stability, and within certain parameters, agility. The driver of a Mazda 4WS-equipped car derives five strategic benefits, over and above the conventional vehicle chassis. 1. Superior cornering stability 2. Improved steering responsiveness and precision 3. High-speed straightline st

13、ability 4. Notable improvement in rapid lane-changing manoeuvres 5. Smaller turning radius and tight-space manoeuvrability at low vehicle speed range The most outstanding advantage of the Mazda 4WS is that it contributes to a notable reduction in driver fatigue over high-speed and extended travellin

14、g. This is achieved by optimally: 1. reducing the response delay to steering input and action and 2. eliminating the vehicles excessive reaction to steering input In essence, by providing the optimum solution to the phenomena researched by the two young Mazda engineers in the early sixties - by the

15、method advocated by them - the 4WS system has emerged as a fully beneficial technology. Strategic Construction The Mazda 4WS consists of a rack-and-pinion front steering system that is hydraulically assisted by a twin-tandem pump main power source, with an overall steering ratio of 14.2:1. The rear

16、wheel steering mechanism is also hydraulically assisted by the main pump and electronically controlled - according to the front steering angle and vehicle speed. The rear steering shaft extends from the rack bar of the front steering gear assembly to the rear steering-phase control unit. The rear st

17、eering system is comprised of the input end of the rear steering shaft, vehicle speed sensors, a steering-phase control unit (determining direction and degree), a power cylinder and an output rod. A centering lock spring is incorporated, which locks the rear system in a neutral (straightforward) pos

18、ition in the event of hydraulic failure. Additionally, a solenoid valve that disengages hydraulic assist (thereby activating the centering lock spring) in case of an electrical failure is included. The 4WS system varies the phase and ratio of the rear-wheel steering to the front wheels, according to

19、 the vehicle speed. It steers the rear wheels toward the opposite phase (direction) of the front wheel during speeds less than 35km/h (22mph) for a tighter turn and neutralizes them (to a straightforward direction, as in a conventional two-wheel steering principle) at 35km/h (22mph). Above that spee

20、d, the system steers toward the same phase-direction as the front wheels, thereby generating an increased cornering force for stability. The maximun steering angle of the rear wheels extends 5 degrees to either left or right, a measurement that Mazda has determined to be optimally effective and natu

21、ral to human sensitivity. Primary Components 1. Vehicle speed sensors Interpret speedometer shelf revolutions and send signal to the electronic computer unit. two sensors, one within the speedometer and the other at the transmission output, are used to crosscheck the other for accuracy and failsafe

22、measures. 2. Steering phase control unit* Conveys to the power steering cylinder booster valve the direction and stroke of rear wheel steering by the combined movement of the control yoke angle and bevel gear revolutions. 3. Electric stepper motor Performs altering of the yoke angle and bevel gear p

23、hasing 4. Rear steering shaft Transmits front wheel steering angle by turning the small bevel gear in the steering phase control unit, which rotates the main bevel gear in the assembly. 5. Control valve Feeds hydraulic pressure to the steering actuator, according to the phase and stroke required for

24、 appropriate rear wheel steering. 6. Hydraulic power cylinder Operates the output rod by hydraulic pressure and steers the rear wheels. It locks the rear wheels in a neutral (straightforward) position with the centering lock spring, which is activated by a solenoid valve in case of failure to ensure

25、 a normal 2WS function for the vehicle. 7. Hydraulic pump. Provides hydraulic pressure to both the front and rear steering systems. Details of Steering Phase Control Unit The steering phase control unit alters the direction and degree of rear wheel steering. It consists of a stepper motor that contr

26、ols the rear steering ratio, a control yoke, a swing arm, a main bevel gear engaged to the rear steering shaft via a small bevel gear, and a control rod connected to the control valve. It operates: a. Opposite phase (direction) steering under 35km/h (22mph) 1. Control Yoke is at an angle activated b

27、y the stepper motor 2. Front wheels are steered to the right. The small bevel gear is rotated in direction X by the rotation of the rear steering shaft. The small bevel gear, in turn, rotates the main bevel gear. 3. Rotation of the main bevel gear causes movement of the control rod toward the contro

28、l valve. 4. Input rod of the control valve is pushed to the right, according to the degree of the control rods movement (determined by the disposition of the swing arm), which is positioned to move in an upward direction, to the right. The rear wheels are thus steered to the left, in an opposite dir

29、ection to the front wheels. 5. As the angle of the control yoke is increased in direction A as vehicle speed decreases, the rear-to-front steering ratio proportionately increases and the vehicles steering lock tightens. b. Same phase (direction) over 35km/h (22mph) The operation of this phase is the

30、 reverse of the opposite phase one, because the control yoke is angled toward positive in this vehicle speed range, as illustrated. The phasing of the swing arm, yoke rod and bevel gear steers the rear wheels toward the right-the same direction as the front wheels. c. Neutral phase, at 35km/h (22mph

31、) The control yokes angle is horizontal (neutral). Thus, the input rod is not affected, even if the control rod is moved with the rotation of the bevel gear unit. As a result, the rear wheels are not steered in this mode. Power Cylinder The movement of the input rod of the control valve unit is tran

32、smitted to the power cylinders spool. The spools displacement to the sleeve causes a pressure difference between the right and left side chambers in the hydraulic power cylinder. The pressure difference overcomes the output shaft load and initiates sleeve movement. The sleeve-power rod assembly is m

33、oved in the direction of the input rod by a proportionate degree. The output rod transmits steering action to the tie rod on either end of the rear wheel steering control-mechanism unit, thereby steering the rear wheels. Fail-Safe Measures The system automatically counteracts possible causes of fail

34、ure, both electronic and hydraulic. In either case, the centering lock spring housed in the steering system unit returns the output rods in the neutral straightforward position, essentially alternating the entire steering system to a conventional 2WS principle. Specifically, if a hydraulic defect sh

35、ould render a reduction in pressure level (by a movement malfunction or a broken driving belt), the rear wheel steering mechanism is automatically locked in a neutral position, activating a low-level warning light. In the event of an electrical failure, such would be detected by a self-diagnostic ci

36、rcuit integrated within the 4WS control unit, which stimulates a solenoid valve and then neutralizes hydraulic pressure and return lines, thereby alternating the system again to that of a 2WS principle. Henceforth, the warning light referencing the 4WS system within the main instrument display is ac

37、tivated, indicating a system failure. 翻譯馬自達公司的速度感應四輪轉向系統三十五年前，兩個馬自達設計師提出了一個遠見的、有計算認為是相當革命性的結論。他們在1962年10月26日日本汽車工程師學會技術會議上 Tadashi Okada博士和Toshiaki工程師總結了他們關于車輛動力學的辛勤研究如下：1.基本特性差別在于過度轉向與不足轉向的量和時間上的延遲和響應。2.汽車在高速狀態下應具備不足轉向特點。3.后方的穩定很大程度上反映出車輪和輪胎。4.控制與穩定的一大進步,可預期的方式自動引導系統后車輪. 這種結論和提法被這兩個工程師提出并為良好懸架技術的研制

38、成立了基金會多年來致力于研究和開發,原有的理論有一定的作用,一些最重要的成就在近代歷史上汽車底盤工程,將在馬自達的系列產品的生產. 這些發展包括雙斜后方的聯系中斷,首先采用原第一輪驅動323K(1980)、馬自達626(1982),然后在更新完善馬自達626. 獲獎的動態跟蹤系統中斷的第二代發票RC7(1985); 并制定電子后方聯系中斷新馬自達929(1987). 而與此同時各種外部壓力和負荷作用與汽車后方的車輪，因為它違背牛頓的運動學原理，這些新系統中斷將這些力量納入4ws效應,積極幫助穩定車輛和機敏. 馬自達的設計師和工程師們的最終目標仍是積極的方法產生積極的控制措施; 四輪轉向體系。1

39、983年馬自達將舉世震驚的概念引入工程車MX02中，并在東京會展上亮相。這輛四門私家轎車在不尋常的長軸距上布置了寬敞的乘客空間，它匯聚許多先進的特點具有高速穩定和低速操控性能的真正意義的4WS系統。后方車輪的量取決于前方雙輪的角度和汽車的速度，而這些是由中央計算機單元控制的。MX-02之后另一個令人振奮的概念車;MX-03于1985年9月第一次在法蘭克福展出。這輛豪華的四座雙門未來派轎車裝配了90年代精確電子控制的4WS系統和不同扭矩均分系統，四輪驅動和強勁的三旋輪發動機。馬自達電子控制四輪轉向系統: 有利的技術馬自達的電子控制、汽車速度感應四輪轉向系統(4ws)驅動雙后輪在一定方向和量上是最

40、適合汽車的速度范圍的。這種系統是機械和液壓系統驅動，伴隨著生產穩定提高,并在某些參數上反應敏捷。馬自達4WS裝備車來自五個戰略利益的驅動，超過了傳統的底盤。1.優秀的轉彎穩定性。2.改良的駕駛響應時間和精度控制。3.高速直線穩定性。4.急速換道的機動性大大改觀。5.更小的轉彎半徑和低速范圍狹小空間的可操縱性。馬自達最顯著的優勢在于4WS系統能顯著降低高速疲勞駕駛和長期駕駛，這是最優化后取得的。1.降低對駕駛輸入和動作的反應延遲。2.消除汽車對駕駛輸入的過度響應。從根本上說，在60 年代初兩位年輕的馬自達工程師通過提供這個最佳解決現象的方法，- 以這種方法他們提倡 -4WS系統已經作為一項完全有

41、利的技術出現。 戰略性建設馬自達4WS系統由兩個串聯泵來提供主要的動力來源的液壓輔助的前置式齒輪齒條副轉向系統，該轉向系的總的傳動比為14.2：1。后面的車輪的轉向依然是靠主泵提供動力的液壓輔助驅動和根據前輪轉角和汽車行駛速度來實現電子控制的裝置。后輪的轉向軸從前轉向器的轉向齒條延伸到轉向控制單元。后面的轉向系統包括轉向軸后的輸入端，車輛速度傳感器，轉向控制單元（確定方向和角度），一個動力氣缸和一個輸入軸。為了以防液壓故障轉向系統上面裝了一個中央鎖彈簧，它將系統鎖止在中間位置，另外一旦發生電類的故障作用在螺旋管閥液體壓力將消失（因此此時將中央鎖彈簧將被開啟）。依據車速的不同變化“”系統因應前輪

42、的變化不斷改變后輪的狀態和比率。當汽車在急轉彎時如果速度小于（）將使汽車的后輪與前輪的狀態相反且（）在使它們失效（直到筆直向前，按照傳統的兩輪轉向原理）。當速度高于（）時系統將于前輪保持同相轉動，因此增加了轉彎時的穩定力。將轉向后車輪的最大轉角無論向左或是向右都增加了。馬自達已經確定了使人感覺到自然和保持人類靈敏性的測量方法。主要組成部分 1. 車輛速度傳感器解析速度計架子的旋轉并把這種信號傳遞到打字計算機單元。有兩個傳感器，一個在速度計內部另一個在傳輸?shù)妮敵龆?，用這樣兩個傳感器是為了使它們兩個相互求證和失效保險。2. 轉向狀態控制單元*通過控制軛角度和錐形齒輪的配合運動將方向和行程傳遞給轉向

43、后輪3. 步進電機執行軛角度的改變和錐形齒輪定相。4. 后輪驅動軸通過控制那些小錐形齒輪來傳遞前輪轉向角，旋轉在組件里的主要錐形齒輪。 5. 控制閥將液壓傳遞給轉向執行機構，根據狀態和行程要求引導合適的后輪轉向。6. 液壓動力氣缸以液壓驅動輸出軸和后輪轉向，它用一個中央鎖止彈簧將后轉向輪鎖在中間位置，如果在不能確保其對一正常的車輛起作用時該鎖將被開啟。7. 液壓泵，給前面兩個提供液壓和后驅動輪。轉向狀態控制的細節轉向控制單元改變轉向后輪的度和方向。它有控制轉向后輪轉向系傳動比的步進電機，一個控制軛， 一只擺動臂，一個通過小錐齒輪連接在后輪轉向軸上的錐齒輪，和一個操縱桿連接控制閥。 它操作： a

44、. 轉向狀態（方向）少于（）的轉向。1. 控制軛在步進電機作用下有一個角度。2. 前輪被轉向右邊。小的錐形齒輪由于轉向后輪軸的旋轉而沿方向旋轉，小的錐形齒輪依次旋轉主要的錐形齒輪。3. 主要錐形齒輪的旋轉引起控制閥操縱桿的運動。4. 控制閥的輸入桿被推到右邊， 根據操縱桿的運動的度(通過擺動臂的安排確定)，被確定位置進入一個向上方向，朝右邊。 后車輪在左側被如此使得轉向后輪對轉向前輪有個相反的轉向。5. 隨著車輛速度的減少控制軛的角度增加，由后到前的轉向系傳動比也要成比例增加而轉向鎖收緊。b.這個階段的操縱與第一個階段的操作相反，這是因為在一定的速度范圍控制軛的轉動角度趨向明顯，如同說明的那樣

45、。擺動臂，軛桿和錐形齒輪與前轉向輪保持相同的狀態。c.中間狀態，以（）控制軛的角度是水平的（中間位置）。因此，這根輸入桿沒有被影響，即使這個操縱桿為錐形齒輪單元所帶動。因此后轉向輪沒有被這種方式所驅動。動力氣缸控制閥單元的輸入軸的運動被傳遞給氣缸線軸。由于線軸相對與套管的位移使得液壓動力氣缸的左右壁室的形成一個壓力差。壓力差克服輸出軸的負荷并使軸套運動。軸套動力軸總成被以相同的比例傳遞到輸入。輸出軸將轉向運動傳遞到后輪的任一轉向控制單元。由此驅動后轉向輪。故障安全保障系統能自動消除電子和液壓可能存在的問題， 無論發生哪種情況，封裝在轉向系統里面的中央鎖止彈簧返回給輸出軸并確保其在中間的位置。本質上是使整個轉向系統符合一個傳統的2WS準則。尤其是一個液壓的缺陷使得壓力水平的降低（一個錯誤的操作或者是安全帶的斷裂），后輪轉向裝置被鎖止在中間位置，并氣動一盞低級的警告燈，如果是一個電子元件的錯誤，那么這個錯誤將被集成在4WS控制單元里面的自診斷回路所探測到，這將促使一個螺線管閥門的開啟然后使液壓無效并且返回到回路里面，因此再次使該系統符合2WS準則。 從今以后，4WS系統在主要儀器內展示的警告燈開動，就表明一個系統故障。