模具英語大全[共21頁]

《模具英語大全[共21頁]》由會員分享，可在線閱讀，更多相關《模具英語大全[共21頁]（21頁珍藏版）》請在裝配圖網上搜索。

1、沖壓模具-零件類punch沖頭 insert入塊(嵌入件) deburring punch壓毛邊沖子 groove punch壓線沖子 stamped punch字模沖子 round punch圓沖子 special shape punch異形沖子 bending block折刀 roller滾軸 baffle plate擋塊 located block定位塊 supporting block for location 定位支承塊 air cushion plate氣墊板 air-cushion eject-rod氣墊頂桿 trimming punch切邊沖子 stiffening rib p

2、unch = stinger 加強筋沖子 ribbon punch壓筋沖子 reel-stretch punch卷圓壓平?jīng)_子 guide plate定位板 sliding block滑塊 sliding dowel block滑塊固定塊 active plate活動板 lower sliding plate下滑塊板 upper holder block上壓塊 upper mid plate上中間板 spring box彈簧箱 spring-box eject-rod彈簧箱頂桿 spring-box eject-plate彈簧箱頂板 bushing bolck襯套 cover plate蓋板 g

3、uide pad導料塊 沖壓模具-模板類top plate上托板（頂板） top block上墊腳 punch set上模座 punch pad上墊板 punch holder上夾板 stripper pad脫料背板 up stripper上脫料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板 die pad下墊板 die holder下夾板 die set下模座 bottom block下墊腳 bottom plate下托板(底板) stripping plate內外打(脫料板) ou

4、ter stripper外脫料板 inner stripper內脫料板 lower stripper下脫料板 沖壓模具-沖壓類plain die簡易模 pierce die沖孔模 forming die成型模 progressive die連續模 gang dies復合模 shearing die剪邊模 riveting die鉚合模 pierce沖孔 forming成型(抽凸,沖凸) draw hole抽孔 bending折彎 trim切邊 emboss凸點 dome凸圓 semi-shearing半剪 stamp mark沖記號 deburr or coin壓毛邊 punch riveti

5、ng沖壓鉚合 side stretch側沖壓平 reel stretch卷圓壓平 groove壓線 blanking下料 stamp letter沖字(料號) shearing剪斷 tick-mark nearside正面壓印 tick-mark farside反面壓印 extension dwg展開圖 procedure dwg工程圖 die structure dwg模具結構圖 material材質 material thickness料片厚度 factor系數 upward向上 downward向下 press specification沖床規格 die height range適用模高

6、 die height閉模高度 burr毛邊 gap間隙 weight重量 total wt.總重量 punch wt.上模重量 塑件模具英語compre sion molding壓縮成型 flash mold溢流式模具 plsitive mold擠壓式模具 split mold分割式模具 cavity型控 母模 core模心 公模 taper錐拔 leather cloak仿皮革 shiver飾紋 flow mark流痕 welding mark溶合痕 post screw insert螺紋套筒埋值 self tapping screw自攻螺絲 striper plate脫料板 piston

7、活塞 cylinder汽缸套 chip細碎物 handle mold手持式模具 encapsulation molding低壓封裝成型、射出成型用模具 two plate兩極式（模具） well type蓄料井 insulated runner絕緣澆道方式 hot runner熱澆道 runner plat澆道模塊 valve gate閥門澆口 band heater環帶狀的電熱器 spindle閥針 spear head刨尖頭 slag well冷料井 cold slag冷料渣 air vent排氣道 welding line熔合痕eject pin頂出針 knock pin頂出銷 retu

8、rn pin回位銷反頂針 sleave套筒 stripper plate脫料板 insert core放置入子 runner stripper plate澆道脫料板 guide pin導銷 eject rod (bar)（成型機）頂業捧 subzero深冷處理 three plate三極式模具 runner system澆道系統 stress crack應力電裂 orientation定向 sprue gate射料澆口，直澆口 nozzle射嘴 sprue lock pin料頭鉤銷(拉料桿) slag well冷料井 side gate側澆口 edge gate側緣澆口 tab gate搭接澆

9、口 film gate薄膜澆口 flash gate閘門澆口 slit gate縫隙澆口 fan gate扇形澆口 dish gate因盤形澆口 diaphragm gate隔膜澆口 ring gate環形澆口 subarine gate潛入式澆口 tunnel gate隧道式澆口 pin gate針點澆口 Runner less無澆道 (sprue less)無射料管方式 long nozzle延長噴嘴方式 sprue澆口;溶渣各式模具英語landed plunger mold 有肩柱塞式模具 burnishing die 擠光模 landed positive mold 有肩全壓式模具 b

10、utton die 鑲?cè)胧綀A形凹模 loading shoe mold 料套式模具 center-gated mold 中心澆口式模具 loose detail mold 活零件模具 chill mold 冷硬用鑄模 loose mold 活動式模具 clod hobbing 冷擠壓制模 louvering die 百葉窗沖切模 composite dies 復合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 組合式模具 double stack mold 雙層模具 multi-cavity mold 多模穴模具 electroform

11、ed mold 電鑄成形模 multi-gate mold 復式澆口模具 expander die 擴徑模 offswt bending die 雙折冷彎模具 extrusion die 擠出模 palletizing die 疊層模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模 porous mold 通氣性模具 duplicated cavity plate 復板模 positive mold 全壓式模具 fantail die 扇尾形模具 pressure die 壓緊模 fishtail die 魚尾形模具

12、profile die 輪廓模 flash mold 溢料式模具 progressive die 順序模 gypsum mold 石膏鑄模 protable mold 手提式模具 hot-runner mold 熱流道模具 prototype mold 雛形試驗?zāi)＞?ingot mold 鋼錠模 punching die 落料模 lancing die 切口模 raising(embossing) 壓花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 無流道冷料模具 sectional die 對合模具 se

13、gment mold 組合模 semi-positive mold 半全壓式模具 shaper 定型模套 single cavity mold 單腔模具 solid forging die 整體鍛模 split forging die 拼合鍛模 split mold 雙并式模具 sprueless mold 無注道殘料模具 squeezing die 擠壓模 stretch form die 拉伸成形模 sweeping mold 平刮鑄模 swing die 振動模具 three plates mold 三片式模具 trimming die 切邊模 unit mold 單元式模具 unive

14、rsal mold 通用模具 unscrewing mold 退扣式模具 yoke type die 軛型模 相關模具英語padding block墊塊 stepping bar墊條 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上墊板 spare dies模具備品 spring 彈簧 bolt螺栓 document folder活頁夾 file folder資料夾 to put file in order整理資料 spare tools location手工備品倉

15、first count初盤人 first check初盤復棹人 second count 復盤人 second check復盤復核人 equipment設備 waste materials廢料 work in progress product在制品 casing = containerazation裝箱 quantity of physical invetory second count 復盤點數量 quantity of customs count 會計師盤,點數量 the first page第一聯 filed by accounting department for reference會

16、計部存查 end-user/using unit(department)使用單位 summary of year-end physical inventory bills 年終盤點截止單據匯總表 bill name單據名稱 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表請與盤點清冊一起送會計部(NHK廠區送財會部) Application status recor

17、ds of year-end physical inventory List and physical inventory card 年終盤點卡與清冊使用狀況明細表 blank and waste sheet NO. 空白與作廢單號 plate電鍍 mold成型 material for engineering mold testing工程試模材料 not included in physical inventory不列入盤點 sample樣品 incoming material to be inspected進貨待驗 description品名steel/rolled steel鋼材 mat

18、erial statistics sheet 物料統計明細表 meeting minutes會議記錄 meeting type 會別 distribution department分發單位 location地點 chairman主席 present members出席人員 subject主題 conclusion結論 decision items決議事項 responsible department負責單位 pre-fixed finishing date預定完成日 approved by / checked by / prepared by核準/審核/承辦 PCE assembly prod

19、uction schedule sheet PCE組裝廠生產排配表 model機鐘 work order工令 revision版次 remark備注 production control confirmation生產確認 checked by初審 approved by核準 department部門 stock age analysis sheet 庫存貨齡分析表 on-hand inventory現有庫存 available material良品可使用 obsolete material良品已呆滯 to be inspected or reworked 待驗或重工 total合計 cause

20、 description原因說明 part number/ P/N 料號 type形態 item/group/class類別 quality品質 prepared by制表 notes說明 year-end physical inventory difference analysis sheet 年終盤點差異分析表 physical inventory盤點數量 physical count quantity帳面數量difference quantity差異量 cause analysis原因分析 raw materials原料 materials物料 finished product成品 se

21、mi-finished product半成品 packing materials包材 good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods處理品 warehouse/hub倉庫 on way location在途倉 oversea location海外倉 spare parts physical inventory list備品盤點清單 spare molds location模具備品倉 skid/pallet棧板 tox machi

22、ne自鉚機 wire EDM線割 EDM放電機 coil stock卷料 sheet stock片料 tolerance工差 score=groove壓線 cam block滑塊 pilot導正筒 trim剪外邊 pierce剪內邊 drag form壓鍛差 pocket for the punch head掛鉤槽 slug hole廢料孔 feature die公母模 expansion dwg展開圖 radius半徑 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺絲 form block折刀 stop pin定位銷 round pierce p

23、unch=die button圓沖子 shape punch=die insert異形子 stock locater block定位塊 under cut=scrap chopper清角 active plate活動板 模具成形方式accurate die casting 精密壓鑄 powder forming 粉末成形 calendaring molding 壓延成形 powder metal forging 粉末鍛造 cold chamber die casting 冷式壓鑄 precision forging 精密鍛造 cold forging 冷鍛 press forging 沖鍛 c

24、ompacting molding 粉末壓出成形 rocking die forging 搖動鍛造 compound molding 復合成形 rotary forging 回轉鍛造 compression molding 壓縮成形 rotational molding 離心成形 dip mold 浸漬成形 rubber molding 橡膠成形 encapsulation molding 注入成形 sand mold casting 砂模鑄造 extrusion molding 擠出成形 shell casting 殼模鑄造 foam forming ?泡成形 sinter forging

25、燒結鍛造 forging roll 軋鍛 six sides forging 六面鍛造 gravity casting 重力鑄造 slush molding 凝塑成形 hollow(blow) molding 中空(吹出)成形 squeeze casting 高壓鑄造 hot chamber die casting 熱室壓鑄 swaging 擠鍛 hot forging 熱鍛 transfer molding 轉送成形 injection molding 射出成形 warm forging 溫鍛 investment casting 精密鑄造 matched die method 對模成形法

26、laminating method 被覆淋膜成形 low pressure casting 低壓鑄造 lost wax casting 脫蠟鑄造 matched mould thermal forming 對模熱成形模 模具成形不良aberration 色差 atomization ?化 bank mark ?料紋 bite 咬入 blacking hole 涂料孔(鑄疵) blacking scab 涂料疤 blister 起泡 blooming 起霜 blow hole 破孔 blushing 泛白 body wrinkle 側壁皺紋 breaking-in 冒口帶肉 bubble 膜泡

27、burn mark 糊斑 burr 毛邊 camber 翹曲 cell 氣泡 center buckle 表面中部波皺 check 細裂痕 checking 龜裂 chipping 修整表面缺陷 clamp-off 鑄件凹痕 collapse 塌陷 color mottle 色斑 corrosion 腐蝕 crack 裂痕 crazing 碎裂 crazing 龜裂 deformation 變形 edge 切邊碎片 edge crack 裂邊 fading 退色 filler speak 填充料斑 fissure 裂紋 flange wrinkle 凸緣起皺 flaw 刮傷 flow mark

28、 流痕 galling 毛邊 glazing 光滑 gloss 光澤 grease pits 污斑 grinding defect 磨痕 haircrack 發裂 haze 霧度 incrustation 水銹 indentation 壓痕 internal porosity 內部氣孔 mismatch 偏模 mottle 斑點 necking 縮頸 nick 割痕 orange peel 橘皮狀表面缺陷 overflow 溢流 peeling 剝離 pit 坑 pitting corrosion 點狀腐蝕 plate mark 模板印痕 pock 麻點 pock mark 痘斑 resin

29、streak 樹脂流紋 resin wear 樹脂脫落 riding 凹陷 sagging 松垂 saponification 皂化 scar 疤痕 scrap 廢料 scrap jam 廢料阻塞 scratch 刮傷/劃痕 scuffing 深沖表面劃傷 seam 裂痕 shock line ?？跀D痕 short shot 充填不足 shrinkage pool 凹孔 sink mark 凹痕 skin inclusion 表皮折疊 straightening 矯直 streak 條狀痕 surface check 表面裂痕 surface roughening 橘皮狀表皮皺折 surgin

30、g 波動 sweat out 冒汗 torsion 扭曲 warpage 翹曲 waviness 波痕 webbing 熔塌 weld mark 焊痕 whitening 白化 wrinkle 皺紋 模具廠零配件air vent vale 通氣閥 anchor pin 錨梢 angular pin 角梢 baffle 調節阻板 angular pin 傾斜梢 baffle plate 折流檔板 ball button 球塞套 ball plunger 定位球塞 ball slider 球塞滑塊 binder plate 壓板 blank holder 防皺壓板 blanking die 落料沖

31、頭 bolster 上下模板 bottom board 澆注底板 bolster 墊板 bottom plate 下固定板 bracket 托架 bumper block 緩沖塊 buster 堵口 casting ladle 澆注包 casting lug 鑄耳 cavity 模穴(模仁) cavity retainer plate 模穴托板 center pin 中心梢 clamping block 鎖定塊 coil spring 螺旋彈簧 cold punched nut 冷沖螺母 cooling spiral 螺旋冷卻栓 core 心型 core pin 心型梢 cotter 開口梢

32、cross 十字接頭 cushion pin 緩沖梢 diaphragm gate 盤形澆口 die approach 模頭料道 die bed 型底 die block 塊形模體 die body 鑄模座 die bush 合模襯套 die button 沖模母模 die clamper 夾模器 die fastener 模具固定用零件 die holder 母模固定板 die lip 模唇 die plate 沖模板 die set 沖壓模座 direct gate 直接澆口 dog chuck 爪牙夾頭 dowel 定位梢 dowel hole 導套孔 dowel pin 合模梢 doz

33、zle 輔助澆口 dowel pin 定位梢 draft 拔模錐度 draw bead 張力調整桿 drive bearing 傳動軸承 ejection pad 頂出襯墊 ejector 脫模器 ejector guide pin 頂出導梢 ejector leader busher 頂出導梢襯套 ejector pad 頂出墊 ejector pin 頂出梢 ejector plate 頂出板 ejector rod 頂出桿 ejector sleeve 頂出襯套 ejector valve 頂出閥 eye bolt 環首螺栓 filling core 椿入蕊 film gate 薄膜形澆

34、口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圓形模板 fixed bolster plate 固定側模板 flanged pin 帶凸緣? flash gate 毛邊形澆口 flask 上箱 floating punch 浮動沖頭 gate 澆口 gate land 澆口面 gib 凹形拉緊? goose neck 鵝頸管 guide bushing 引導襯套 guide pin 導梢 guide post 引導柱 guide plate 導板 guide rail 導軌 head punch

35、頂?沖頭 headless punch 直柄沖頭 heavily tapered solid 整體模蕊盒 hose nippler 管接頭 impact damper 緩沖器 injection ram 壓射柱塞 inlay busher 嵌入襯套 inner plunger 內柱塞 inner punch 內沖頭 insert 嵌件 insert pin 嵌件梢 king pin 轉向梢 king pin bush 主梢襯套 knockout bar 脫模杵 land 合模平坦面 land area 合模面 leader busher 導梢襯套 lifting pin 起模頂? lining

36、 內襯 locating center punch 定位中心沖頭 locating pilot pin 定位導梢 locating ring 定位環 lock block 壓塊 locking block 定位塊 locking plate 定位板 loose bush 活動襯套 making die 打印沖子 manifold block 歧管檔塊 master plate 靠模樣板 match plate 分型板 mold base 塑膠模座 mold clamp 鑄模緊固夾 mold platen 模用板 moving bolster 換模保持裝置 moving bolster plat

37、e 可動側模板 one piece casting 整體鑄件 parallel block 平行墊塊 paring line 分模線 parting lock set 合模定位器 pass guide 穴型導板 peened head punch 鑲?cè)胧經_頭 pilot pin 導? pin gate 針尖澆口 plate 襯板pre extrusion punch 頂擠沖頭 punch 沖頭 puncher 推桿 pusher pin 襯套梢 rack 機架 rapping rod 起模桿 re-entrant mold 凹入模 retainer pin 嵌件梢 retainer plate

38、 托料板 return pin 回位梢 riding stripper 浮動脫模器 ring gate 環型澆口 roller 滾筒 runner 流道 runner ejector set 流道頂出器 runner lock pin 流道拉梢 screw plug 頭塞 set screw 固定螺絲 shedder 脫模裝置 shim 分隔片 shoe 模座之上下模板 shoot 流道 shoulder bolt 肩部螺絲 skeleton 骨架 slag riser 冒渣口 slide(slide core) 滑塊 slip joint 滑配接頭 spacer block 間隔塊 spac

39、er ring 間隔環 spider 模蕊支架 spindle 主軸 sprue 注道 sprue bushing 注道襯套 sprue bushing guide 注道導套 sprue lock bushing 注道定位襯套 sprue puller 注道拉料? spue line 合模線 square key 方鍵 square nut 方螺帽 square thread 方螺紋 stop collar 限位套 stop pin 止動梢 stop ring 止動環 stopper 定位停止梢 straight pin 圓柱? stripper bolt 脫料螺栓 stripper bush

40、ing 脫模襯套 stripper plate 剝料板 stroke end block 行程止梢 submarine gate 潛入式澆口 support pillar 支撐支柱/頂出支柱 support pin 支撐梢 supporting plate 托板 sweep templete 造模刮板 tab gate 輔助澆口 taper key 推拔鍵 taper pin 拔錐梢/錐形梢 teeming 澆注 three start screw 三條螺紋 thrust pin 推力銷 tie bar 拉杵 tunnel gate 隧道形澆口 vent 通氣孔 wortle plate 拉絲

41、模板模具工程系列 1 GB/T 2-1985 緊固件 外螺紋零件的末端 Fasteners-Ends of parts with external thread 2 GB/T 8-1988 方頭螺栓 C級 Square head bolts-Product grade C 3 GB/T 10-1988 沉頭方頸螺栓 Flat countersunk square neck bolts 4 GB/T 11-1988 沉頭帶榫螺栓 Flat countersunk nib bolts 5 GB/T 12-1988 半圓頭方頸螺栓 Cup head square neck bolts 6 GB/T

42、13-1988 半圓頭帶榫螺栓 Cup head nib bolts 7 GB/T 15-1988 大半圓頭帶榫螺栓 Cup head nib bolts with large head 8 GB/T 22-1976 小六角頭導頸螺栓 Bolts, small hexagon head with fit neck 9 GB/T 23-1976 小六角頭螺桿帶孔螺栓 Bolts, small hexagon head with hole through the shank 10 GB/T 24-1976 小六角頭螺桿帶孔導頸螺栓 Bolts, small hexagon head with fi

43、t neck and hole through the shank11 GB/T 25-1976 小六角頭頭部帶孔螺栓 Bolts, small hexagon head with holes through the head 12 GB/T 26-1976 小六角頭頭部帶孔導頸螺栓 Bolts, small hexagon head with fit neck and holes through the head 13 GB/T 27-1988 六角頭鉸制孔用螺栓 A和B級 Hexagon fit bolts-Product grade A and B 14 GB/T 28-1988 六角頭

44、螺桿帶孔鉸制孔用螺栓 A和B級 Hexagon fit bolts with Split pin hole on shank-Product grade A and B 15 GB/T 29.1-1988 六角頭頭部帶槽螺栓 A和B級 Hexagon bolts with slot on head-Product grade A and B 16 GB/T 29.2-1988 十字槽凹穴六角頭螺栓 Cross recessed hexagon bolts with indentation 17 GB/T 31.1-1988 六角頭螺桿帶孔螺栓 A和B級 Hexagon bolts with s

45、plit pin hole on shank-Product grade A and B 18 GB/T 31.2-1988 六角頭螺桿帶孔螺栓 細桿 B級 Hexagon bolts with split pin hole on shank-Reduced shank-Product grade B 19 GB/T 31.3-1988 六角頭螺桿帶孔螺栓 細牙 A和B級 Hexagon bolts with split pin hole on shank-Fine pitch thread-Product grade A and B 20 GB/T 32.1-1988 六角頭頭部帶孔螺栓 A

46、和B級 Hexagon bolts with wire holes on head-Product grade A and B 21 GB/T 32.2-1988 六角頭頭部帶孔螺栓 細桿 B級 Hexagon bolts with wire holes on head-Reduced shank-Product grade B 22 GB/T 32.3-1988 六角頭頭部帶孔螺栓 細牙 A和B級 Hexagon bolts with wire holes on head-Fine pitch thread-Product grade A and B 23 GB/T 35-1988 小方頭螺

47、栓 B級 Square head bolts with small head-Product grade B 24 GB/T 37-1988 T型槽用螺栓 Bolts for T-Slot 25 GB/T 38-1976 螺栓 技術條件 Bolts-Technical requirements 26 GB/T 39-1988 方螺母 C級 Square nuts-Product grade C 27 GB/T 41-1986 1 型六角螺母 C 級 Hexagon nuts-Style 1-Product grad C 28 GB/T 56-1988 六角厚螺母 Hexagon thick n

48、uts 29 GB/T 61-1976 螺母 技術條件 Nuts-Technical requirements 30 GB/T 62-1988 蝶形螺母 Wing nuts31 GB/T 63-1988 環形螺母 Lifting nuts 32 GB/T 65-1985 開槽圓柱頭螺釘 Slotted cheese head screws 33 GB/T 67-1985 開槽盤頭螺釘 Slotted pan head screws 34 GB/T 68-1985 開槽沉頭螺釘 Slotted countersunk head screws 35 GB/T 69-1985 開槽半沉頭螺釘 Slo

49、tted raised countersunk head screws 36 GB/T 70-1985 內六角圓柱頭螺釘 Hexagon socket cap head screws 37 GB/T 71-1985 開槽錐端緊定螺釘 Slotted set screws with cone point 38 GB/T 72-1988 開槽錐端定位螺釘 Slotted set screws with cone point 39 GB/T 73-1985 開槽平端緊定螺釘 Slotted set screws with flat point 40 GB/T 74-1985 開槽凹端緊定螺釘 Slo

50、tted set screws with cup point41 GB/T 75-1985 開槽長圓柱端緊定螺釘 Slotted set screws withlong dog point 42 GB/T 77-1985 內六角平端緊定螺釘 Hexagon socket set screws with flat point 43 GB/T 78-1985 內六角錐端緊定螺釘 Hexagon socket set screws with cone point 44 GB/T 79-1985 內六角圓柱端緊定螺釘 Hexagon socket set screws with dog point 4

51、5 GB/T 80-1985 內六角凹端緊定螺釘 Hexagon socket set screws with cup point 46 GB/T 83-1988 方頭長圓柱球面端緊定螺釘 Square set screws with long dog point and rounded end 47 GB/T 84-1988 方頭凹端緊定螺釘 Square set screws with cup point 48 GB/T 85-1988 方頭長圓柱端緊定螺釘 Square set screws with long dog point 49 GB/T 86-1988 方頭短圓柱錐端緊定螺釘

52、Square set screws with short dog point and cone end 50 GB/T 89-1976 螺釘 技術條件 Screws-Technical requirements51 GB/T 90-1985 緊固件驗收檢查、標志與包裝 Acceptance inspection,marking and packaging of fasteners 52 GB/T 91-1986 開口銷 Split pins 53 GB/T 93-1987 標準型彈簧墊圈 Single coil spring lock washers-Normal type 54 GB/T 9

53、4.1-1987 彈性墊圈技術條件 彈簧墊圈 Specifications for spring washers-Single coil spring lock washers 55 GB/T 94.2-1987 彈性墊圈技術條件 齒形、鋸齒鎖緊墊圈 Specifications for spring washers-Toothed lock and serrated lock washers 56 GB/T 94.3-1987 彈性墊圈技術條件 鞍形、波形彈性墊圈 Specifications for spring washers-Curved and wave spring washers

54、 57 GB/T 95-1985 平墊圈-C級 Plain washers-Product grade C 58 GB/T 272-1993 滾動軸承 代號方法 Rolling bearing-Identification code 59 GB/T 273.1-1987 滾動軸承 圓錐滾子軸承 外形尺寸方案 Rolling bearings Tapered roller bearings-Boundary dimensions 60 GB/T 273.3-1988 滾動軸承 向心軸承 外形尺寸方案 Rolling bearings Radial bearings-Boundary dimens

55、ions 61 GB/T 274-1991 滾動軸承 裝配倒角極限 Rolling bearing chamfer dimension limits 62 GB/T 275-1993 滾動軸承與軸和外殼的配合 Shaft and housing fits for rolling bearings 63 GB/T 276-1994 滾動軸承 深溝球軸承 外形尺寸 Rolling bearings-Deep groove ball bearings-Boundary dimensions 64 GB/T 280-1964 帶氈封圈的單列向心球軸承 結構型式和基本尺寸 Rolling bearing

56、s-Single-row radial ball bearings withfelt seals-Types and basic dimensions 65 GB/T 281-1994 滾動軸承 調心球軸承 外形尺寸 Rolling bearings-Self-aligning ball bearings-Boundary dimensions 66 GB/T 283-1994 滾動軸承 圓柱滾子軸承 外形尺寸 Rolling bearings-Cylindrical roller bearings-Boundary dimensions 67 GB/T 285-1994 滾動軸承 雙列圓柱滾

57、子軸承 外形尺寸 Rolling bearings-Double row cylindrical roller bearings-Boundary dimensions 68 GB/T 286-1964 雙列向心球面滾子軸承 結構型式和基本尺寸 Rolling bearings-Double -row radial spherical roller bearings-Types and basic dimensions 69 GB/T 288-1994 滾動軸承 調心滾子軸承 外形尺寸 Rolling bearings-Self-aligning roller bearings-Boundar

58、y dimensions 70 GB/T 289-1964 滾針軸承 結構型式和基本尺寸 Needle roller bearings-Types and basic dimensions 71 GB/T 291-1964 螺旋滾子軸承 結構型式和基本尺寸 Rolling bearings with helically wound cylindrical rollers-Types and basic dimensions 72 GB/T 292-1994 滾動軸承 角接觸球軸承 外形尺寸 Rolling bearings-Angular contact ball bearings-Bound

59、ary dimensions 73 GB/T 294-1994 滾動軸承 三點和四點接觸球軸承 外形尺寸 Rolling bearings-Three point and four point contact ball bearings-Boundary dimensions 74 GB/T 296-1994 滾動軸承 雙列角接觸球軸承 外形尺寸 Rolling bearings-Double row angular contact ball bearings-Boundary dimensions 75 GB/T 297-1994 滾動軸承 圓錐滾子軸承 外形尺寸 Rolling beari

60、ngs-Tapered roller bearings-Boundary dimensions 76 GB/T 299-1995 滾動軸承 雙列圓錐滾子軸承 外形尺寸 Rolling bearings-Metric double row tapered roller bearings-Boundary dimensions 77 GB/T 300-1995 滾動軸承 四列圓錐滾子軸承外形尺寸 Rolling bearings-Four row tapered roller bearings-Boundary dimensions 78 GB/T 301-1995 滾動軸承 推力球軸承 外形尺寸

61、 Rolling bearings-Thrust ball bearings-Boundary dimensions 79 GB/T 304.1-1988 關節軸承 分類 Spherical plain bearings Classification 80 GB/T 304.2-1988 關節軸承 代號方法 Spherical plain bearings Identification code81 GB/T 304.3-1990 關節軸承 配合 Spherical plain bearings-Fits 82 GB/T 304.9-1981 向心關節軸承 技術條件 Spherical pla

62、in radial bearings, joint type-Technical requirements 83 GB/T 304.10-1989 關節軸承公差 Spherical plain bearings-Tolerances 84 GB/T 307.1-1994 滾動軸承 向心軸承 公差 Rolling bearings-Radial bearings-Tolerances 85 GB/T 307.2-1995 滾動軸承 測量和檢驗的原則及方法 Rolling bearings-Measuring and gauging principles and methods 86 GB/T 307.3-1996 滾動軸承 通用技術規則 Rolling bearings-General technical regulations 87 GB/T 307.4-1994 滾動軸承 推力球軸承 公差