《減速器英文資料及翻譯》由會員分享，可在線閱讀，更多相關《減速器英文資料及翻譯（9頁珍藏版）》請在裝配圖網上搜索。
1、英文原文：Mineral product monorail reduction gear synopsis1 what is reducer Reducer is a dynamic communication agencies, the use of gear speed converters, motor rotational speed reducer to the Rotary to be few, and have greater torque institutions. 1.1 The reducer role1.1.1 velocity at the same time incr
2、ease the output torque, torque output ratio by motor output by slowdown, but the attention should be paid to exceed the rated torque reducer. 1.1.2 the speed at the same time reduce the inertia load, the inertia of deceleration than reduced to the square. We can look at the General Motors has a valu
3、e of inertia. 1.2 The type of reducerGeneral helical gear reducer has reducer (including parallel shaft helical gear reducer, a worm reducer, bevel gear reducer, etc.), planetary gear reducer, Cycloid reducer, a worm reducer, a planetary friction CVT mechanical machines. 1.3 Common reducer1.3.1 worm
4、 reducer is the main characteristics of a reverse self-locking function, can be larger than a slowdown, input shaft and output shaft axis is not the same, nor in the same plane. But generally larger, transmission efficiency is not high, the accuracy is not high. 1.3.2 Harmonic Drive reducer is contr
5、ollable using flexible components to transfer elastic deformation and dynamic movement, not volume, high precision, but the disadvantage is that flexible wheel limited life, impatient shocks, rigidity and pieces of metal relatively poor. Not too high speed input. 1.3.3 planetary reducer its comparat
6、ive advantage is compact structure, the return gap small, high precision, and have a long life span rated output torque can be done great. However, a price slightly expensive, the requirements of parts before assembly ： 1.3.3.1 Rolling cleaning with gasoline, kerosene other parts cleaning. All parts
7、 and cabinet not allowed to have any impurities exist. Gear box and the inner wall (Worm), unprocessed surface has not been coated twice erosion-resistant oil paint box has the outer surface coated primer and paint color (color requested by host). 1.3.3.2 Parts coated with a face wash after lubrican
8、ts. 2 the requirements of installation and adjustment 2.1 Rolling installation Rolling bearing inner ring should be installed at the shaft shoulder close to gap must not pass 0.05 mm thick Cypriot feet. 2.2 Bearing axial clearance Of the clearance can not be adjusted bearings (such as deep groove ba
9、ll bearings), axial clearance of 0.25 to 0.4 mm; the clearance adjustable bearing axial clearance numerical table. Click Tapered Roller Bearings axial clearance; angular contact ball bearing axial clearance. 2.3 Gear (Worm) meshing tooth space available Cypriot side foot of lead or pressure. Will be
10、 lead wire on the alveolar, and then turning gear and squash lead wire, measuring two teeth side was crushed lead wire thickness and the size of which is adjacent teeth. 2.4 Tooth contact dot cylinder gear tooth contact Dot 2-10-4; bevel gear tooth contact Dot 2-11-4; Gearing contact Dot 2-12-4. 3 s
11、eal requirements 3.1 Box partition between the surface does not allow any pads filled, but can be coated or water glass sealant to ensure that the seal; 3.2 Assembly, the bolt tightening box, before using 0.05 mm Cypriot-foot inspection Covers Block with me and between the sealing surface; 3.3 Shaft
12、 seal should stretch to smear grease. The seal should be installed in strict accordance with the requirements. 4 lubrication requirements 4.1 Rationally determine the types of lubricants and greases and grades 4.2 Bearing lubrication fat, grease filled in the general Fatliquor space can be 1 / 2 to
13、2 / 3. 4.3 Lubricants should be regularly replaced, the new reducer used for the first time, the operation of oil-7 14 days, according to the situation can be after every 3 to 6 months for first oil. 5 the test requirements 5.1 Empty operation: at rated speed is, anti-running 1 to 2 hours; 5.2 Load
14、test: at rated speed, rated load operation, the oil temperature balance to date. On the gear reducer, requested the pool temperature is not more than 35 , bearing temperature rise no more than 40 ; the worm reducer, requested the pool temperature not more than 60, bearing temperature of not more tha
15、n 50 . 6 packaging and transportation requirements 6.1 Protruding shaft and its annex should Oiler packaging; 6.2 Handling, lifting may not use screw rings and lug all of the above technical requirements are not necessarily listed, and sometimes also by other projects, mainly by the specific design
16、requirements. 7 Technical requirements 7.1 Assembly, all parts cleaning with kerosene, gasoline Rolling cleansing, while the existence of any debris. Oil is not painted wall corrosion coatings twice; 7.2 Backlash with lead wire mesh test of not less than 0.16 mm, lead wire Backlash may not exceed th
17、e smallest of the four times; 7.3 Used Tu-color dot test. Tooth high point of contact by not less than 40% of contact spots on teeth not less than 50 per cent. Can be used when necessary, grinding or scraping after grinding to improve contacts; 7.4 Bearing axial clearance should be adjusted: 40 0.05
18、 - 0.1 mm, 55 0.08 - 0.15 mm; 7.5 Test reducer subdivision surface, the contact surface and seal, oil spills are not allowed. Split-Tu allowed to paint or water glass seal and allow the use of any filler; 7.6 Engine lubricants to the contents N100 provisions height. 8 GEAR INTRODUCTION8.1 Abstract:
19、The important position of the wheel gear cant falter in traditional machine and modern machines.The wheel gear mainly install the direction that delivers the dint at the principal axis box. The passing to process to make them can is divided into many model numbers, used for many situations respectiv
20、ely.8.2 Key words: Wheel gearIn the force analysis of spur gears, the forces are assumed to act in a single plane. We shall study gears in which the forces have three dimensions. The reason for this, in the case of helical gears, is that the teeth are not parallel to the axis of rotation. And in the
21、 case of bevel gears, the rotational axes are not parallel to each other. There are also other reasons, as we shall learn.Helical gears are used to transmit motion between parallel shafts. The helix angle is the same on each gear, but one gear must have a right-hand helix and the other a left-hand h
22、elix. The shape of the tooth is an involutes helicoids. If a piece of paper cut in the shape of a parallelogram is wrapped around a cylinder, the angular edge of the paper becomes a helix. If we unwind this paper, each point on the angular edge generates an involutes curve. The surface obtained when
23、 every point on the edge generates an involutes is called an involutes helicoids.The initial contact of spur-gear teeth is a line extending all the way across the face of the tooth. The initial contact of helical gear teeth is a point, which changes into a line as the teeth come into more engagement
24、. In spur gears the line of contact is parallel to the axis of the rotation; in helical gears, the line is diagonal across the face of the tooth. It is this gradual of the teeth and the smooth transfer of load from one tooth to another, which give helical gears the ability to transmit heavy loads at
25、 high speeds. Helical gears subject the shaft bearings to both radial and thrust loads. When the thrust loads become high or are objectionable for other reasons, it may be desirable to use double helical gears. A double helical gear (herringbone) is equivalent to two helical gears of opposite hand,
26、mounted side by side on the same shaft. They develop opposite thrust reactions and thus cancel out the thrust load. When two or more single helical gears are mounted on the same shaft, the hand of the gears should be selected so as to produce the minimum thrust load.Crossed-helical, or spiral, gears
27、 are those in which the shaft centerlines are neither parallel nor intersecting. The teeth of crossed-helical fears have point contact with each other, which changes to line contact as the gears wear in. For this reason they will carry out very small loads and are mainly for instrumental application
28、s, and are definitely not recommended for use in the transmission of power. There is on difference between a crossed helical gear and a helical gear until they are mounted in mesh with each other. They are manufactured in the same way. A pair of meshed crossed helical gears usually have the same han
29、d; that is, a right-hand driver goes with a right-hand driven. In the design of crossed-helical gears, the minimum sliding velocity is obtained when the helix angle are equal. However, when the helix angle is not equal, the gear with the larger helix angle should be used as the driver if both gears
30、have the same hand.Worm gears are similar to crossed helical gears. The pinion or worm has a small number of teeth, usually one to four, and since they completely wrap around the pitch cylinder they are called threads. Its mating gear is called a worm gear, which is not a true helical gear. A worm a
31、nd worm gear are used to provide a high angular-velocity reduction between nonintersecting shafts which are usually at right angle. The worm gear is not a helical gear because its face is made concave to fit the curvature of the worm in order to provide line contact instead of point contact. However
32、, a disadvantage of worm gearing is the high sliding velocities across the teeth, the same as with crossed helical gears.Worm gearing are either single or double enveloping. A single-enveloping gearing is one in which the gear wraps around or partially encloses the worm. A gearing in which each elem
33、ent partially encloses the other is, of course, a double-enveloping worm gearing. The important difference between the two is that area contact exists between the teeth of double-enveloping gears while only line contact between those of single-enveloping gears. The worm and worm gear of a set have t
34、he same hand of helix as for crossed helical gears, but the helix angles are usually quite different. The helix angle on the worm is generally quite large, and that on the gear very small. Because of this, it is usual to specify the lead angle on the worm, which is the complement of the worm helix a
35、ngle, and the helix angle on the gear; the two angles are equal for a 90-deg. Shaft angle.中文譯文：1 什么是減速器 減速器是一種動力傳達機構，利用齒輪的速度轉換器，將馬達的回轉數減速到所要的回轉數，并得到較大轉矩的機構。 1.1 減速器的作用 1.1.1降速同時提高輸出扭矩，扭矩輸出比例按電機輸出乘減速比，但要注意不能超出減速器額定扭矩。 1.1.2 減速同時降低了負載的慣量，慣量的減少為減速比的平方。大家可以看一下一般電機都有一個慣量數值。 1.2 減速器的種類 一般的減速器有斜齒輪減速器(包括平行軸
36、斜齒輪減速器、蝸輪減速器、錐齒輪減速器等等)、行星齒輪減速器、擺線針輪減速器、蝸輪蝸桿減速器、行星摩擦式機械無級變速機等等。 1.3 常見減速器 1.3.1 蝸輪蝸桿減速器的主要特點是具有反向自鎖功能，可以有較大的減速比，輸入軸和輸出軸不在同一軸線上，也不在同一平面上。但是一般體積較大，傳動效率不高，精度不高。 1.3.2 諧波減速器的諧波傳動是利用柔性元件可控的彈性變形來傳遞運動和動力的，體積不大、精度很高，但缺點是柔輪壽命有限、不耐沖擊，剛性與金屬件相比較差。輸入轉速不能太高。 1.3.3 行星減速器其優點是結構比較緊湊，回程間隙小、精度較高，使用壽命很長，額定輸出扭矩可以做的很大。但價格
37、略貴、對裝配前零件的要求 ： 1.3.3.1滾動軸承用汽油清洗，其他零件用煤油清洗。所有零件和箱體內不許有任何雜質存在 。箱體內壁和齒輪（蝸輪）等未加工表面先后涂兩次不被機油侵蝕的耐油漆，箱體外表 面先后涂底漆和顏色油漆（按主機要求配色）。 1.3.3.2零件配合面洗凈后涂以潤滑油。 2 安裝和調整的要求 2.1滾動軸承的安裝 滾動軸承安裝時軸承內圈應緊貼軸肩，要求縫隙不得通過0.05mm 厚的塞尺。 2.2 軸承軸向游隙 對游隙不可調整的軸承（如深溝球軸承），其軸向游隙為0.250.4mm；對游隙可調整 的軸承軸向游隙數值見表。點擊查看圓錐滾子軸承軸向游隙；角接觸球軸承軸向游隙。 2.3 齒
38、輪（蝸輪）嚙合的齒側間隙 可用塞尺或壓鉛法。即將鉛絲放在齒槽上，然后轉動齒輪而壓扁鉛絲，測量兩齒側被 壓扁鉛絲厚度之和即為齒側的大小。 2.4齒面接觸斑點圓柱齒輪齒面接觸斑點2-10-4；圓錐齒輪齒面接觸斑點2-11-4；蝸桿傳動接觸斑點2-12-4。 3 密封要求 31 箱體剖分面之間不允許填任何墊片，但可以涂密封膠或水玻璃以保證密封； 3.2 裝配時，在擰緊箱體螺栓前，應使用0.05mm的塞尺檢查箱蓋和箱座結合面之間的密封性； 3.3軸伸密封處應涂以潤滑脂。各密封裝置應嚴格按要求安裝。 4 潤滑要求 4.1 合理確定潤滑油和潤滑脂類型和牌號。 4.2 軸承脂潤滑時，潤滑脂的填充量一般為可加
39、脂空間的1/22/3。 4.3 潤滑油應定期更換，新減速器第一次使用時，運轉714天后換油，以后可以根據情況每隔36個月?lián)Q一次油。 5 試驗要求 5.1 空載運轉：在額定轉速下正、反運轉12小時； 5.2 負荷試驗：在額定轉速、額定負荷下運轉，至油溫平衡為止。 對齒輪減速器，要求油池溫升不超過35,軸承溫升不超過40； 對蝸桿減速器，要求油池溫升不超過60,軸承溫升不超過50。 6 包裝和運輸要求 6.1 外伸軸及其附件應涂油包裝； 6.2 搬運、起吊時不得使用吊環螺釘及吊耳以上技術要求不一定全部列出，有時還需另增項目，主要由設計的具體要求而定。 7 技術要求 7.1 裝配前，所有零件用煤油清
40、洗，滾動軸承用汽油清洗，不許有任何 雜物存在。內壁涂上不被機油腐蝕的涂料兩次； 7.2 嚙合側隙用鉛絲檢驗不小于0.16mm，鉛絲不得大于最小側隙的4倍； 7.3 用涂色法檢驗斑點。按齒高接觸點不小于40%；按齒長接觸斑點不小于50%。必要時可用研磨或刮后研磨以便改善接觸情況； 7.4 應調整軸承軸向間隙：40為0.05-0.1mm,55為0.08-0.15mm; 7.5 檢驗減速器剖分面、各接觸面及密封處，均不許漏油。剖分面允許 涂以密封油漆或水玻璃，不允許使用任何填料； 7.6 機座內裝N100潤滑油至規定高度。 8 齒輪和軸的介紹8.1 摘要:在傳統機械和現代機械中齒輪的重要地位是不可動
41、搖的。齒輪主要安裝在主軸箱來傳遞力的方向。通過加工制造它們可以分為許多的型號，分別用于許多的場合。8.2 關鍵詞:齒輪在直齒圓柱齒輪的受力分析中，是假定各力作用在單一平面的。我們將研究作用力具有三維坐標的齒輪。因此，在斜齒輪的情況下，其齒向是不平行于回轉軸線的。而在錐齒輪的情況中各回轉軸線互相不平行。斜齒輪用于傳遞平行軸之間的運動。傾斜角度每個齒輪都一樣，但一個必須右旋斜齒，而另一個必須是左旋斜齒。齒的形狀是一濺開線螺旋面。如果一張被剪成平行四邊形（矩形）的紙張包圍在齒輪圓柱體上，紙上印出齒的角刃邊就變成斜線。如果我展開這張紙，在血角刃邊上的每一個點就發生一漸開線曲線。直齒圓柱齒輪輪齒的初始接
42、觸處是跨過整個齒面而伸展開來的線。斜齒輪輪齒的初始接觸是一點，當齒進入更多的嚙合時，它就變成線。在直齒圓柱齒輪中，接觸是平行于回轉軸線的。在斜齒輪中，該先是跨過齒面的對角線。它是齒輪逐漸進行嚙合并平穩的從一個齒到另一個齒傳遞運動，那樣就使斜齒輪具有高速重載下平穩傳遞運動的能力。斜齒輪使軸的軸承承受徑向和軸向力。當軸向推力變的大了或由于別的原因而產生某些影響時，那就可以使用人字齒輪。雙斜齒輪（人字齒輪）是與反向的并排地裝在同一軸上的兩個斜齒輪等效。他們產生相反的軸向推力作用，這樣就消除了軸向推力。當兩個或更多個單向齒斜齒輪被在同一軸上時，齒輪的齒向應作選擇，以便產生最小的軸向推力。交錯軸斜齒輪或
43、螺旋齒輪，他們是軸中心線既不相交也不平行。交錯軸斜齒輪的齒彼此之間發生點接觸，它隨著齒輪的磨合而變成線接觸。因此他們只能傳遞小的載荷和主要用于儀器設備中，而且肯定不能推薦在動力傳動中使用。交錯軸斜齒輪與斜齒輪之間在被安裝后互相捏合之前是沒有任何區別的。它們是以同樣的方法進行制造。一對相嚙合的交錯軸斜齒輪通常具有同樣的齒向，即左旋主動齒輪跟右旋從動齒輪相嚙合。在交錯軸斜齒設計中，當該齒的斜角相等時所產生滑移速度最小。然而當該齒的斜角不相等時，如果兩個齒輪具有相同齒向的話，大斜角齒輪應用作主動齒輪。蝸輪與交錯軸斜齒輪相似。小齒輪即蝸桿具有較小的齒數，通常是一到四齒，由于它們完全纏繞在節圓柱上，因此
44、它們被稱為螺紋齒。與其相配的齒輪叫做蝸輪，蝸輪不是真正的斜齒輪。蝸桿和蝸輪通常是用于向垂直相交軸之間的傳動提供大的角速度減速比。蝸輪不是斜齒輪，因為其齒頂面做成中凹形狀以適配蝸桿曲率，目的是要形成線接觸而不是點接觸。然而蝸桿蝸輪傳動機構中存在齒間有較大滑移速度的缺點，正像交錯軸斜齒輪那樣。蝸桿蝸輪機構有單包圍和雙包圍機構。單包圍機構就是蝸輪包裹著蝸桿的一種機構。當然，如果每個構件各自局部地包圍著對方的蝸輪機構就是雙包圍蝸輪蝸桿機構。著兩者之間的重要區別是，在雙包圍蝸輪組的輪齒間有面接觸，而在單包圍的蝸輪組的輪齒間有線接觸。一個裝置中的蝸桿和蝸輪正像交錯軸斜齒輪那樣具有相同的齒向，但是其斜齒齒角的角度是極不相同的。蝸桿上的齒斜角度通常很大，而蝸輪上的則極小，因此習慣常規定蝸桿的導角，那就是蝸桿齒斜角的余角；也規定了蝸輪上的齒斜角，該兩角之和就等于90度的軸線交角。9
減速器英文資料及翻譯
