齒輪泵的結構改進設計含開題及16張CAD圖

齒輪泵的結構改進設計含開題及16張CAD圖,齒輪泵,結構,改進,改良,設計,開題,16,cad 英文原文 4.3 Flow in an Oil Injected Screw Compressor Figure 4-27 Comparison of pressure change for turbulent and laminar flow calculations The difference in the compressor flow obtained from laminar and turbulent calcu-lations is presented in Figure 4-28. The mass flows at suction and discharge are given as functions of the shaft angle. On average, 4% higher low is calculated with the turbulent model. The difference was greater at the discharge end of the compressor, both in the mean value and in the amplitude. This agrees with the re-sults obtained from the approximate calculations where turbulent transport through clearances is significant. The difference in flow obtained at the suction end is, on average, less than 3%. This shows that a compressor with a large suc-tion opening has no significant dynamical losses, although turbulence exists in the compressor low pressure domains. It is expected that the difference between the laminar and turbulent flow calculations will be smaller for higher discharge pres-sures and lower compressor speeds. Figure 4-28 Comparison of fluid flow at inlet and exit of screw compressor The integral parameters obtained from both the laminar and turbulent numerical models are presented in Table 4-2. According to these results, it can be concluded that turbulence has some influence on the screw compressor. Its effect is greater at lower pressure ratios and low compressor speeds. More detailed insights into the results obtained from the k-model of turbulence can be found in the following four figures; Figure 4-29 shows the kinetic energy of turbulence. The dissipation rate is presented in Figure 4-30, the turbulent vis-cosity in Figure 4-31 and the dimensionless distance from wall y+ is given in Figure 4-32. Figure 4-29 Kinetic energy of turbulence within the screw compressor 4.3 Flow in an Oil Injected Screw Compressor Figure 4-30 Dissipation rate within the screw compressor Figure 4-31 Turbulent viscosity within the screw compressor Figure 4-32 Dimensionless distances from the wall within the compressor The results in all these diagrams are presented in horizontal sections through the blow hole areas on the suction and discharge side of the compressor, in vertical sections through the rotor axes and in cross sections at suction and discharge. The kinetic energy of turbulence, dissipation, turbulent viscosity and y+ are all high for the lobes exposed to the suction domains. All these gradually die out towards discharge. The dissipation rate is extremely high in the clearance gaps between the rotors, as shown in Figure 4-30, while in the other domains it is significantly lower. On the other hand, y+ is small in the clearance gaps while in the main do-mains at suction it has higher values, as shown in Figure 4-32. 4.3.5 The Influence of the Mesh Size on Calculation Accuracy Most calculations in this book are presented for numerical meshes with an average number of 30 cells along one interlobe and a similar number of time steps selected for the rotor to rotate between two interlobe positions. The numerical mesh for thecompressor in this example consists of about 450,000 cells of which About 322,000 numerical cells define the rotor domains. This was a convenient numberof cells to use with a PC computer with an ATHLON 800 processor and 1GB of RAM, which was used for this study. Although the results obtained on that mesh appeared to be satisfactory and agreed well with the experimental data, an investi-gation of the influence of the mesh size on the calculation accuracy had to be con-ducted. For that reason, two additional meshes were generated for the same com-pressor. A smaller one was generated with 20 points along the rotor interlobe, which gave 190,000 cells on both rotors while the other compressor parts were mapped with almost the same number of cells as originally. The overall number of numerical cells was about 353,000. A lower number of cells on the rotors results in a geometry, which does not follow the rotor shape precisely, and the intercon-nection between rotors would possibly become inappropriate. This number of nu-merical cells is probably the lowest for which reliable results can be obtained. Thelargest numerical mesh generated for this investigation consists of 45 numerical cells along the rotor interlobe. That gave 515,520 cell on the rotors and 637,000 cells for the entire compressor domain. This was the biggest numerical mesh that could be loaded into the available computer memory without disc swapping dur-ing the solution. These three numerical meshes are presented in Figure 4-33 in the cross section perpendicular to the rotor axes. Figure 4-33 Three different mesh sizes for the same compressor The results of the calculations are presented in Figure 4-34 in the form of a pres-sure-angle diagram, and in Figure 4-36 as a discharge flow-angle diagram. The first diagram shows how the calculated working pressures for all three investi-gated mesh sizes agree with the measurements. The lowest number of cells gives the highest pressure in the working chamber and vice versa. As a result of that, the consumed power is changed slightly, from 42 kW obtained with the smallest mesh to slightly less then 41 kW for the largest mesh. The difference between the two is less then 3%. This situation is shown in Figure 4-35. The diagram shows the larg-est difference within the cycle to be in the discharge area of the compressor. Some difference is also visible in the middle area of the diagram which seems to be a consequence of the leakage flows obtained with smaller meshes between the ro-tors. In that area, the mesh is probably too coarse to capture all the oscillations which appear in the flow. Figure 4-34 P-alpha diagrams for three different mesh sizes Figure 4-35 Compressor power calculated with three different mesh sizes 4.3 Flow in an Oil Injected Screw Compressor Figure 4-36 Discharge flow rates for different mesh sizes Figure 4-37 Integral flow rate and Specific power obtained with different mesh sizes Diagrams of discharge flow as a function of rotation angle are given in Figure4-36. The coarser mesh shows less oscillation in the flow then the finer meshes. However, the mean value of the flow remained the same for all three mesh sizes, as shown in Figure 4-37. Specific power is calculated from the values obtained previously. It shows a slight fall in value as the number of computational cells is increased. The results obtained with the three different mesh sizes for the compressor in-vestigated here give the impression that the calculation conducted for the com-pressor on an average size of the mesh with 25 to 30 numerical cells along the ro-tor interlobe is sufficiently accurate. 中文譯文 4.3 噴油螺桿壓縮機的流量 圖4-27計算比較湍流和層流壓力變化 如圖4-28為在計算吸氣和排氣的質量流量功能軸角中獲得的壓縮機流從層流和湍流差異。總體而言，湍流模型比流從層流高4%，無論是在平均值和振幅，壓縮機的排出端是最大的，通過計算近似結果獲得間隙顯著的湍流輸送的重。在吸入端獲得的流量差異的平均值，小于3％。這表明，具有大的吸入端的壓縮機吸氣開口沒有任何顯著的動力損失，雖然在壓縮機低壓域存在湍流。這是預期的層流和湍流之間的差異計算將提高排氣壓力和減小壓縮機速度。 圖4-28根據流體的流動比較螺桿式壓縮機的入口和出口 從層流和湍流數值模型的積分獲得的參數，如表4-2中。根據這些結果，可以得出結論，在湍流的螺桿式壓縮機上有一定的影響。其效果是在壓力越小，流速越大。從第k湍流模型獲得的結果的更詳細的分析，可以發現在以下四個數字，如圖4-29的湍流的動能。圖4-30，圖4-31動蕩對粘度和無量綱距離墻Y +耗散率，如圖4-32。 圖4-29螺桿壓縮機內的湍流動能 圖4-30螺桿式壓縮機內的損耗率 圖4-31螺桿壓縮機內的湍流粘度 圖4-32從墻壁內壓縮機的量綱距離通過吸入閥和排出側的壓縮機的結果列于所有這些圖中，在通過轉子軸的吸入閥和排出的橫截面的垂直剖面上的吹孔區域的水平部分。動蕩，耗散，湍流粘度和y+的動能都是高暴露在吸域葉上，所有這些逐漸消亡走向放電。耗散率非常高，轉子之間的間隙差距，如圖4-30所示，而在其他領域，它是顯著較低。另一方面，如圖4-32所示，+小的間隙中，在主電源處于吸入它具有較高的值。 4.3.5 網格大小對計算精度的影響 在計算這本書中的大部分平均30個細胞的數量沿一個和類似用于轉子之間旋轉兩位置的數量的選擇步驟嚙合。在這個例子中包括約45萬個細胞數值網格，其中約322,000數字單元格定義轉子域。這是用于這項研究為了方便使用的細胞數量與PC電腦的Athlon800處理器和1GB的RAM，雖然網格上，得到的結果似乎是令人滿意的，并與實驗數據相同，但在康秀紅，杜強，李殿中，李依依的調查中，影響網格尺寸的計算精度的到的結果是可靠的。本次調查由45個數字單元格沿轉子的數值t網。這給了整個壓縮機515,520細胞轉子和637,000細胞領域。這是最大的數值的網格，可以在裝入光盤交換過程中溶液沒有可用的計算機內存。圖4-33中介紹這在轉子軸垂直的截面中的三個數值的嚙合。圖4-37獲得不同的網目尺寸和比功率的積分流量。圖36中給出的是作為旋轉角度的函數的排出流，粗網格顯示振蕩流，但是，所有三個網目尺寸仍然是流量的平均值，如在圖4-37所示，從先前得到的值計算比功率。它顯示了輕微的下降值，計算增加的細胞數目。得到的結果是在研究壓縮機的平均面積為25至30數值RO涵道。出于這個原因，產生相同的壓縮機的是兩個額外的嚙合。產生一個較小以20分沿的轉子，這兩個轉子給了19萬個細胞，而其它的壓縮機部件幾乎相同被最初的細胞數量映射。數值細胞的總?cè)藬?shù)為353,000左右。在較低的數字的單元格的幾何形狀，這并不精確地說，按照轉子的形狀和轉子之間的互連，連接在轉子上的結果就可能是不恰當?shù)?。這個數值的細胞的數量可能是最低的，得到的結果是可靠的。本次調查由45個數字單元格沿轉子的數值t網。這給了整個壓縮機515,520細胞轉子和637,000細胞領域。這是最大的數值的網格，可以在裝入光盤交換過程中溶液沒有可用的計算機內存。圖4-33中介紹這在轉子軸垂直的截面中的三個數值的嚙合。 圖4-33網格大小相同的三鐘不同的壓縮機 在圖4-34中壓力角圖的計算結果，圖4-36中的排放流角圖。第一個圖表顯示如何計算研究所有三個門控網目尺寸的工作壓力。最低的細胞數量給出了工作腔的最高壓力，反之亦然。消耗功率略有變化，從42千瓦獲得的最小的最大網格，略小宇1千瓦。兩者之間的差異小于3%。這種情況如圖4-35所示，該圖顯示了在周期內所述壓縮機的排放區的最大的差異。這些差異也顯示在圖的中間區域，這是泄露流器RO-小網格之間獲得的結果。在這方面，可能是網格捕捉太粗以致所有的震蕩出現流動。 圖4-34 三種不同網格大小的P-阿爾法圖 圖4-35 三種不同的網格尺寸壓縮機功率計算 圖4-36 不同網格尺寸放電流速 圖4-37 獲得的不同網目尺寸和比功率的積分流量 圖36中給出的是作為旋轉角度的函數的排出流，粗網格顯示振蕩流，但是，所有三個網目尺寸仍然是流量的平均值，如在圖4-37所示，從先前得到的值計算比功率。它顯示了輕微的下降值，計算增加的細胞數目。得到的結果是在研究壓縮機的平均面積為25至30數值RO-器的細胞沿網格進行計算三種不同的網目尺寸的壓縮機是足夠準確的。