接線柱注塑成型工藝與模具設計【兒童益智積木】【樂高積木】【一模八腔】【側抽芯】

接線柱注塑成型工藝與模具設計【兒童益智積木】【樂高積木】【一模八腔】【側抽芯】,兒童益智積木,樂高積木,一模八腔,側抽芯,接線柱注塑成型工藝與模具設計【兒童益智積木】【樂高積木】【一模八腔】【側抽芯】,接線柱,注塑,成型,工藝,模具設計,兒童,益智,積木 設計說明書 畢業設計題目：接線柱注塑成型工藝與模具設計 系 部 專 業 班 級 學生姓名 學 號 指導教師 2014年 4月 22 日 內容摘要 本次設計的是塑料接線柱塑料模具，體現了典型塑料模的設計要求、內容及方向，有一定的設計意義。通過對該模具的設計，加強了設計者對塑料模設計基礎知識的理解和運用，為設計更復雜的塑料模具做好了鋪墊。 本設計運用塑料模具工藝及模具設計的基礎知識，首先分析了產品的性能要求，并選定合適的材料，然后進行了型腔分布設計以及三維立體建模，以選取合適的分型面；最后分析了產品的特征，便于確定模具的設計參數、設計要點及卸件裝置。 本設計采用了一模八腔的結構。成型原理如下：首先將松散的粒狀或粉末狀成型物料從注塑機的料斗送入高溫的機筒內加熱、熔融、塑化。使之成為黏流溶體，然后再柱塞或螺桿的高壓推動下，以很大的流速通過機筒前端的噴射嘴注射進入溫度較低的閉合模具中，經過一段時間的保壓冷卻定型時間后，即可取出注射成型的塑膠接線柱。 成型過程如下:動定模板合模后，由注塑機注射將已加熱到熔融狀態的材料注射入型腔，經過主流道分流道，充滿型腔后，經過一定的冷卻保壓后，動定模板分離，側抽芯機構工作，抽芯完成后，壓力機推動推板用頂桿推出制件，手動取出即可。 關鍵字：塑料模、材料、一模八腔、側抽芯、成型原理、成型過程 English abstract This design is about plastic binding post mold.it presents the typical plastic mold design requirements.there is a great significant in the concent and the directions.by designing the mold,it strengths the comprehension and using about the basic knowledge of designers.This is a good bedding to design the more complex plastic mold. The design uses basic knowledge of plastic mold art.and mold designing.At first ,we analyze the products performance.and select the proper material and then design the mold cavity and it’s distribution.three dimension molding to choose the proper mold joint.At last,analyze the character of the product.In order to identify the design,data is the key point of the design and the equipment of the products. The design use the construction of exactly eight cavity,these are the principle,first,we send the inattentive particulate matter and powder matter to the high heat machine hopper to heat,melt,and make them into dissolve matter,and then under the high pressure of plunger and screw,they go in a quick speed,through the melting jet in the head of the machine shotting the lower closed model.After the pressure of dynamic fixed clamping becomes cold.We can withdraw the fashioned binding post. Following are the processes:the shot machine send the materials to the melting stoves. Passing by the primary and the secondary roads.Filling with the mold and after the cold pressure ,they separated.The side core-pulling began to work.When it comes to an end,the pressure machine push the knockout plate,and then,withdraw it with your hand. The keyword：plastic mold、material、Exactly eight cavity、Side core-pulling、Forming principle、Molding process