應急燈外殼的注塑模具設計【兩板模一模兩腔優秀課程畢業設計含8張CAD圖紙帶開題報告+外文翻譯】-zsmj35

應急燈外殼的注塑模具設計【兩板模一模兩腔優秀課程畢業設計含S8張CAD圖紙帶開題報告+外文翻譯】-zsmj35

應急燈外殼的注塑模具設計【兩板模一模兩腔】

摘  要

本論文主要研究的是應急燈外殼注塑模具的設計方法。本文首先介紹了選題的依據以及選這個課題的意義，并簡單介紹了注塑模具的發展現狀。然后分析了應急燈外殼制件的工藝特點，包括結構工藝性、成型特性與條件、材料性能等，并選定了成型設備。接著述說了應急燈外殼注塑模的分型面選擇、模具基本結構及模架的選定及型腔數目的選定及布置，重點論述了成型零件、澆注系統、、脫模機構、合模導向機構以及冷卻系統的設計。而后選定標準模架和模具材料，并校核注射機的相關工藝參數，如最大注射量、注塑壓力等。最后闡述模具的工作原理，以及對安裝運行過程中可能出現的問題予以總結、分析，并給于了對應的解決方法。

本文論述的應急燈外殼注塑模具采用兩板式結構，采用一模兩腔的型腔布置，最后通過推板將制件推出。在設計模具的時候，需用到SoliWorks軟件進行模擬，以確定型芯型腔及澆口位。此次應急燈外殼注塑模具的設計各項參數必須來源可靠、選擇準確、計算無誤，其中最大注射量及注射壓力是計算的關鍵。在工藝性上保證不影響操作的同時盡量做到了加工操作簡單、方便。

本設計是在傳統的應急燈上進行了創新，設計采用最領先技術LED顯示，并把電池裝在燈內部，外部也更美觀。外殼的尺寸大小適中，模架也較好的選擇，模具整體不大，采用整體安裝。

關鍵詞：應急燈外殼；注塑模；兩板模；澆注系統；脫模機構

Abstract

The designing methods of injection mould of the Emergency light shell are mainly introduced in this paper. This paper introduces the topic basis and the significance of choosing thistopic, and briefly introduces the development status of injection mold.And then analyzes the process characteristics of emergency lamp shellparts, including the structure, characteristics and conditions of moldingprocess, material properties, and select the molding equipment.Then tell the type emergency lamp shell injection mold, mold surfacestructure and mold base selection and the number of cavities selection andlayout, emphasis, gating system, forming parts, demoulding mechanism,clamping mechanism and the cooling system design.Finally the selected standard mold and mold material, and process parameters of injection machine check, such as the maximum injection volume, injection pressure etc.. The working principle of the die, as well as to the possible problems in the process of installation and operation are summarized, analysis, and give the corresponding solutions.

Shell of emergency lamp injection mold in this paper adopts two plate structure, the layout of the cavity of a mould with two cavities, the push platewill work out.In the design of mold, use the SoliWorks software to simulate, in order to determine the core and cavity and runner position.Must choose accurate, reliable, accurate calculation of design parameters of the emergency lamp shell injection mold, the largest injection quantityand injection pressure is the key.In the process that does not affect the operation at the same time as far as possible the process has the advantages of simple operation, convenient.

This design is the innovation in the emergency lights on the traditionaldesign, using the most advanced technology of LED display, and the battery installed in the light of internal, external and more beautiful.Moderate size of shell mold, is the better choice, overall not die, the wholeinstallation.

Keyword: Emergency light shell;Injection mould;Threepence mould;Gating system;Moulding mechanism ; Space parting institutions

目    錄

引言 1

第1章  應急燈外殼工藝性分析 4

1.1 材料性能 4

1.2 成型特性和條件 4

1.3 結構工藝性 4

1.4 產品幾何形狀分析 5

1.5 應急燈外殼注塑工藝參數的確定 9

1.6 初選注射機的型號和規格 9

第2章  應急燈外殼注塑模具的結構設計 11

2.1 分型面的選擇 11

2.2 確定模具基本結構及模架的選定 12

2.3 確定型腔的數量和布局 12

2.4澆注系統設計 13

2.4.1主流道設計 13

2.4.2 分流道截面設計及布局 14

2.4.3 澆口設計及位置選擇 15

2.4.4 澆口套的設計 16

2.5 注塑模成型零部件設計 17

2.5.1 成型零部件尺寸分析 17

2.5.2塑件收縮率的影響 17

2.5.3型腔、型芯結構設計 18

2.5.4 成型零件工作尺寸計算 20

2.6 合模導向機構設計 20

2.7 脫模、推出機構設計 21

2.7.1 推出機構的組成 21

2.7.2 推出機構的分類 21

2.7.3 推出機構的設計原則 21

2.8冷卻系統設計 23

2.9 模架及模具材料的選擇 24

第3章  注射機相關參數校核 25

3.1 最大注射量的校核 25

3.2 注射壓力校核 26

3.3 鎖模力校核 26

3.4 模具厚度的校核 26

3.5 成型零部件強度校核計算 27

第4章  模具的工作原理及安裝、調試 28

4.1 模具的工作原理 28

4.2 模具的安裝 29

4.3 試模 29

結論 31

謝  辭 32

參考文獻 33

【詳情如下】【需要咨詢購買全套設計請加QQ1459919609】

CAXA圖紙副本

型腔板A1.dwg

復位桿A2.dwg

定位圈A2.dwg

帶肩導套A2.dwg

應急燈塑件圖A1.dwg

應急燈外殼的注塑模具設計.doc

應急燈外殼的注塑模具設計任務書.doc

應急燈外殼的注塑模具設計開題報告.doc

應急燈模具裝配圖A0.dwg

支撐塊A2.dwg

文件清單.txt

翻譯原文.pdf

翻譯譯文.doc

頂桿A2.dwg