年產4500噸二硫化碳尾氣處理系統及冷凝器設計（全套CAD圖+說明書+開題報告+翻譯）
年產4500噸二硫化碳尾氣處理系統及冷凝器設計（全套CAD圖+說明書+開題報告+翻譯）,年產,二硫化碳,尾氣,處理,系統,冷凝器,設計,全套,cad,說明書,仿單,開題,報告,講演,呈文,翻譯
摘 要
本次設計介紹了二硫化碳尾氣處理系統的工藝設計。它包括總工藝流程設計，冷凝器的設計及校核，計量罐的設計及校核。
冷凝器的設計是本次設計的重點。根據實際情況最終確定選用應用最為廣泛的間壁式換熱設備為此次所需冷凝器。它的設計步驟為先進行傳熱計算，然后進行冷凝器的尺寸計算，最后進行強度計算和校核。設計前的熱力計算是本次設計的難點與重點。由于冷凝的介質中含有不凝性氣體，所以加大了熱力學傳熱計算這部分的計算難度。冷凝器的設計包括冷凝器上的筒體、封頭、管箱、管板、換熱管、折流板、拉桿、接管、開孔補強、支座、法蘭等的設計、計算與核算。
計量罐的設計包括筒體、封頭、接管、開口補強、液面計及支座的設計和校核，是本次設計的一個重要組成部分。
關鍵詞：總工藝流程；冷凝器；計量罐；
Abstract
Introduction to the Design of the exhaust gas treatment system of the carbon disulfide Process Design. It includes the total flow structural design, the condenser design and verification, measurement can design and verification.
Condenser is designed to be the focus of this design. According to the actual situation to determine the final selection of the most widely used heat exchanger equipment partitions required for the condenser. It is designed to carry out the steps for the first heat transfer calculation, then the size of the condenser, the final calculation and check for strength. Design before the thermal calculation is difficult in this design and focus. As a result of condensation of the medium containing non-condensable gas, it increased the heat transfer calculation of the thermodynamic calculation of the difficulty of this part. Condenser design includes the cylinder, head, control boxes, control panels, heat exchanger, baffle, bar, take over, opening reinforcement, bearing, flange, such as design, computing and accounting.
measurement can design includes cylinder, head, take over, opening reinforcement, and the bearing surface of the design and verification, is an important design component.
Key words: total flow; condenser; measurement can;
目錄
前 言 1
1二硫化碳尾氣處理系統工藝設計 2
1.1國內外二硫化碳生產概況 2
1.2工藝流程設計 3
2冷凝器的設計 4
2.1冷凝器的結構選型 4
2.2熱力計算 4
2.2.1設計參數 4
2.2.2熱量衡算 5
2.3冷卻水量的計算 6
2.4初定冷凝器尺寸 6
2.4.1試選管子 7
2.4.2校核水的流速 8
2.5冷凝器結構設計 12
2.5.1管束分程 12
2.5.2管子排列 12
2.5.3冷凝器管板的結構形式 13
2.5.4管子與管板、管板與殼體的連接 14
2.5.5 冷凝器殼體設計 14
2.5.6 冷凝器封頭設計 15
2.5.7折流板設計 16
2.5.8拉桿設計 17
2.5.9進出口管設計 17
2.5.10進出口管法蘭設計 18
2.5.11開孔補強 19
2.5.12管箱設計及管箱與殼體接管的位置 20
2.5.13支座設計 22
2.5.14校核冷凝器應力 23
2.5.15管板校核 26
2.5.16 水壓試驗校核 40
2.5.17壓力試驗 40
3 計量罐的設計 41
3.1筒體設計 41
3.2封頭設計 42
3.3開孔與接管及補強圈設計 43
3.4液面設計 43
3.5裕量校核 44
3.6支座設計 44
3.7水壓試驗 45
附 錄 46
參考文獻 63
謝 辭 64
- ⅰ-
收藏